how to attach veranda deck boards without grooved edge

When using grooved edge boards, our hidden deck fastening system installs between the deck boards, fastening them to the joists with no visible deck screw heads on the walking surface. This precision also Hideaway Hidden Fastening System start clip used to install Transcend grooved edge composite decking 

Cut decking that overlaps over the sides of the deck with a carbide blade on a circular saw. Cutting at a 90 degree angle creates a smooth edge that does not detract from the overall look of the finished deck. Add a border of fascia around the edges of the exterior boards to hold them in place. Installing Veranda brand deck 

There are a variety of hidden fastener systems available for use to install decking. Many manufactured decking materials offer deck boards that are sold with a grooved edge for use with hidden fasteners. You can also router the deck clips. It is important to note that pregrooved boards do not have a standard groove size.

product from packaging, lift the board as opposed to sliding on its edge. • Avoid sliding or dragging tools and equipment during the construction process. . install. Railing supports must NOT be attached to Zuri. Decking. • Surface mounted railings cannot be mounted to or through Zuri. Joist Spacing: Cellular PVC is not as 

grooved edge of the board should be a minimum of 1" (3 cm) from the board side. 5. Secure the first deck board by face fastening with a stainless steel or composite deck screw in each pre drilled hole. DO NOT OVER TIGHTEN THE SCREWS. 6. On opposite side of first deck board, insert a. Veranda ArmorGuard Hidden 

Hidden fastener systems allow you to attach composite boards securely to the joists with no nail or screw heads to mar their appearance. They are clips usually made of stainless steel that screw to the joists and hook into grooves in the sides of the boards. If the boards you're using don't have these grooves, it isn't 

Do not install decking directly to an existing or solid surface. • Sleeper installation: Minimum joist height is 1.5 in, installed level, in direction of water runoff and directly to a solid sub structure. Create adequate ventilation for the deck by widening side to side spacing between boards to ¼ in. with a maximum of 3/8 in. gap.

In this how to video, learn to create a maintenance free deck with TOH general contractor Tom Silva. Error loading player: No playable sources found. X. Steps: 1. Measure the deck Fasten the deck board with composite decking screws along the edge closest to house; drive one screw into each joist. 7. Install a hidden 

Pre drill with a 3/16 bit and install a screw every 16 to 24 inches along the edge. This screw is strong so you can drive it just slightly below the surface of the deck board or you can screw it down 3/8 of an inch or more and plug the hole. On composite decking do not drill a pilot hole and run the screw below the surface about 

The newest generation of hidden deck fasteners, featuring Mantis technology provides a hidden fastener solution for grooved decking made from PVC, . Align the deck board edge with the inside of the Finishing Clip leg with two holes, fasten to the joist. OVERHAN G FINISH: Fasten the Finish Clip leg with one hole into 

If you are using hidden deck fasteners, there may be occasions when you need to cut a groove into a square edge deck board. AZEK Deck; Legacy; Earthwood Evolutions ; TwinFinish ; Transcend ; Select ; Enhance ; Horizons;  

Grooved Edge Board. Actual Dimensions: 1 in x 5.5 in (2.5 cm x 14 cm). Connector Clip (stainless steel). Universal Starter Clip. Universal Fastener (glass filled nylon) . deck's edge, you can install screws placed perpendicularly at the recommended distance, at minimum of 1 in (2.5 cm) from the board end and edge, without 

(14 cm x 2.4 cm x 610 cm). Veranda ArmorGuard Decking. Veranda Decking. Square Edge. Square Edge. Grooved. Fascia .75 in. x 11.25 in. x 8 or 12 ft. (2cm x 29 cm Surface fasten using heavy gauge (#9 or #10) quality composite deck screws. Joists. 16" o.c. (41 cm). Deck Boards. 12" o.c. (31 cm). Joists Deck Boards.

Expert advice on how to install and work with TREX and other composite decking materials, how to cut and fasten TREX, and framing for composite decking. A clean cut should not leave any loose material, but if you need to clean up an edge, do not use a sander. Sanders will mar the finish and in many